Kit Red
Kit Red
I have a candy apple red 9-piece Ludwig Rocker drum kit from the late 80's. How much is it worth?
It's wrapped, not laquered. It's in great condition, very few scratches. All original hardware and stands.
I'd say if the condition is near mint as you claimed and everything is in fine working order, you may be able to get upwards of 5g on the high end and maybe 1500 on the low.
I guess it all depends on the market your selling it on. Check ebay out to see what others are going for and never take the first offer unless its juicy.
Good luck and rock on!
 |
 RED SPEAKER SURROUND REPAIR KIT FOR CERWIN VEGA 12  US $18.99
|
 RED FOAM SURROUND REPAIR KIT FOR CERWIN VEGA 8 US $15.99
|
 Diamond Multimedia MSP50R Mini Rocker Mono Red Kit US $25.74
|
| Powered by phpBay Pro |
|
|
|
|
|
|
|
|
|
|
Laptops might have been designed with portability and long battery life in mind, but they weren't designed for comfort. Use a laptop on your coffee table for more than five minutes and you're transformed into a warped and twisted, hunchbacked visage of a human being, proclaiming thanks that she did, indeed, give us water and the internets.
What we need is something that raises and angles your fine laptop into a more human-friendly angle. And while we do thank the clever clogs for pointing out a book shoved under the back of the laptop would do just that, it's hardly what we'd call an elegant solution as we try and raise ourselves above the level of tramp.
As it happens it's easy enough to grab an acrylic sheet and bend the two ends to produce an effective custom laptop stand. You just need to vary the height of the back-end to adjust the angle. If you're running a performance laptop then it's easy to add cooling via an extra case fan powered off a USB port.
An A3-sized acrylic sheet should be fine for most laptops enough. We've opted for a 3mm thick sheet that costs less than $8, but for laptops over 3kg use a sheet 4mm thick.
What you will need
A3 acrylic sheet
Case fan
USB cable
Protective gloves
Hot-air paint stripper
Soldering kit
Clamps
Workbench
Wire wool
Instructions
1. At its heart this make is superbly easy, but due to the hot-air gun, we'd recommend a workbench.
2. Make sure you get a decent-sized acrylic sheet, we'll need about 7 to 10cm for the rear fold and 3 to 5cm for the front fold then 20 to 30cm for the main section. As it turns out an A3 sheet is about right and widely available on eBay.
3. Measure and clamp the sheet in place and peel any protective plastic well out of the way. Pop on protective gloves and use the heat gun on a 'cool' 300°C setting. Evenly heat the sheet where you want the fold. This will take a good few minutes.
4. Once you've made the back fold. Do the same for the front. We bent this completely back on itself to make a comfortable fold if we rest it on our legs.
5. That could be it right there, but we're going to add extra cooling. Flip the laptop over and mark out where the cooling vents are, drill/cut slowly otherwise you'll crack the plastic.
6. Take an existing USB cable and strip a suitable length of cable.
7. Choose a low-power fan as it'll only be supplied with 5v rather than the required 12v. Solder the black and red connections together.
8. To make a neat finish, counter sink screw holes in the plastic, so the fan screws will be flush.
9. Our final touch is to add a strip of silicon rubber or you could use rubber pads to stop the laptop from slipping.
10. Done.
Subscribe to Sandra Prior's Online Newsletter and get up to date Computer Technology News delivered right to your email box for free. See website for details http://usacomputers.rr.nu and http://sacomputers.rr.nu.