Round Wall
setting up 27'round fixed wall pool.have area leveled and sand in. have put blockes and track around. what now
need to know how to put in liner and walls so walls wont fall down when putting in overlap liner.
You need to pick your day and your helpers. Don't try putting up a wall, no matter how many hands you have or bracing, unless it's calm out. It's a disater waiting to happen.
The more people the merrier, but it can be done on a calm day , with 3 people. . Now your prep is done, figure out where the filter equipment is going to go. The wall is usually rolled with the skimmer cut out within the first few feet. That's where your equipment will be. Once you've figured that out, that's where you will start unrolling the wall, on it's end (make sure you have it right side up). Unroll 2 feet and put in track, unroll 2 feet and put in track. Have a helper behind you to put on the small top tubes at this time. If they stay behind you and place the tubes as you move and put into track, the wall will be fairly stable. Have a pal hold onto that start end tho, never know if a wind will come up. Move methodically and slowly. Adding pals to recent sections around the pool wall. Every 8 feet will be more than enough. When you get to the end, likely it won't match. That's why nothing is pagged to anything at this point, you'll have to do a little wiggle and sometimes move a large section around to get it to fit. Remember, the track must fit the wall, it you can do something about, the wall is the wall, it's a fixed length you can't do anything about. Do all moves a bit at a time, just one person, the rest still holding their section of wall. The guy that stood there holding the first bit of wall has the job of lining up the bolt holes. Give him a screw driver to put into the first correct holes that match up, to hold that position Lightly bolt it ( heads inside pool) and continue wiggling and using that screw driver to help pry the rest to match up. When most of the bolt holes are done ( for sure top and as far down as you can reach) start moving that round upper track around so's it joins under the top caps. Install the caps (don't screw the caps on yet) and uprights( these you can screw).Check for level at each cap as you go. When done, you can jump in the pool at an upright that you've put a top rail on each side and fastened, carefully (on a curve section in an oval). Finnish putting the bolts in the wall and duct tape over them. Dampen the sand and trowel it out smooth and level, a little cove at the wall is a nice touch. Jump out at an upright. That last little bit, you'll have to smooth out with a fine broom from outside the pool. Remove the caps and the two rails you installed, have your plastic strips spread around the pool and ready. The skimmer may need to be fastened at this time. It depends on what type it is. One type needs to be fastened directly to the wall now, minus the face plate, the other later, when the pool is filling. Consult your documentation that came with the skimmer. Liner time. Two ways to do this, depending on the number of hands you have.If you have plenty of help, keep everything sharp a hunderd yards away. Lift it up over the top of the wall, trying not to let it touch any part of the pool and walk it out. Don't drag it on that nice bottom you just did. Move it around to fit and use those plastic strips to tack the liner in place.
If there's only 3 of you, temporarily fasten your top rails in place. This will hold the walls steady. Still take care not to let the liner get pulled on the rails, it may catch a corner. Have someone there to lift it over. Having few hands, will, unfortunately mean, that liner will get dragged across that smooth bottom, causing some impressions. It can't be avoided that's why it's best to have as many people as you can muster, for this.
Someone in socks has to jump in and kick the liner gently into the wall to get rid of wrinkles that you couldn't pull out, from outside the pool. Don't worry about small packing creases, these will be fine when the water gets in. Stay near the wall and tread lightly. If the sand is still damp, you won't get many footprints, if any. Start a shop vac up (big one preferable) and stick it in through the return hole ponted down, about a foot, between the liner and the wall. Duct tape around the hose to make a good seal and have someone hold the liner against the wall at the skimmer, to seal there as well. Look for wrinkes and move them out to the walls, adjusting the liner up the wall, if needed as the shop vac pulls the liner taught. If you're happy with the result, put on and fasten all your top rails, checking the wall here and there for vertical. In the case of an oval, either shim or tap down your butress's. Fasten your bottom plates to your stones if you wish. They won't be going anywhere, but it's a nice touch. If everything looks good start filling. when there's 2 inches in the pool, jump in and do another wrinkle hunt. The weight of the water pressing down, will stop any footprints, if you tread carefully. If you find any bothersome ones, sometimes a kettle of boiling water, applied right at the wrinkle will make it pliable to move out. Continue to fill the pool. Get you filter equipment set up. When the pool is about half way filled, you can remove the shop vac. Install the skimmer and returns, just before the water level reaches them. That way there's less stress as the liner moves a bit during the last part of the fill. For the return, just cut an X inside the wall hole and push the fitting through, trim the excess vinyl on the outside of the threads, install the nut to snug plus 1/4 turn. The skimmer is next. You may have already installed the skimmer body, if not, and it's the type that's a fasten through face plate/wall/skimmer, do it now. Probe for the holes carefully. You'll feel them through the vinyl. Fasten the faceplate and gasket through the wall to the skimmer. When done, and everything is peachy, cut out the vinyl on the inside of the skimmer face plate. Hook up all your plumbing before the pool gets up . I suggest putting a ball valve in both lines before the equipment, to enable you to isolate the filter and pump equipment from the pool. It will also keep your feet dryer, when cleaning out the pump basket, that pool will want to drain out there and can sometimes make putting the pump lid back on difficult. That's it,
Use DataComm Electronics 1-gang recessed low voltage cable plates to install low voltage cables behind your flat panel TV, your amplifier, or other audio/video devices.
|
|
Polk Audio's RCi Series in-wall speakers let you deliver sound to every room in your home without sacrificing a single square inch of valuable floor or shelf space, and the RC60i in-wall speakers are no exception...
|
|
The most convenient Jawbone yet comes with an easy-to-operate On/Off slide switch and one button that provides unparalleled convenience. It also has standard micro-USB charging technology, so you don't have to carry more cables...
|
|
VP 11B - Grounded Europe Adapter - USA to Europe Heavy Duty Adaptor Plug German Schuko: Converts 2 Or 3 Pin American Plug To Euro/German Shucko Plug. This Is A Grounded Adapter Plug. This will not convert the voltage from 220V to 110V...
|
|
Wall Clock, 13-1/4, Arabic Numerals, Black Frame
|
|
JBL 2-Way Ceiling speaker with a 8" titanium laminate mid base driver and a 1" titanium laminate tweeter.
|
|
Professional 2-6" Camera Bracket, MADE OF SOLID METAL. All parts are interchangeable and can customized into 12 different combinations! This neat little kit gives you a lot of versatility for creative indoor and outdoor mount applications, even around corners and near windows, etc...
|
|
The Honeywell RCWL300A P3 Premium Portable Wireless Door Chime and Push Button makes it easy to replace your home's generic doorbell ring with a chime tune that better fits your individual style. This chime is also compatible with a wide range of optional security accessories that can help you safeguard your home and family, and it comes complete with a pre-programmed bell push button...
|
|
Pyle 8in round ceilingspkr pair spkr pair -1/2 pivoting polymer dome tweeter -frequency response: 50hz-20khz -overall: 10 1/2 x 3 1/2 d -cut out: 9 3/8...
|
|
Wall Clock, 9 Round, Arabic Numerals, Silver/White
|
|
US $54.98
